Next Article in Journal
Improving the Performance of Vegetable Leaf Wetness Duration Models in Greenhouses Using Decision Tree Learning
Previous Article in Journal
Hydrology of the Sirba River: Updating and Analysis of Discharge Time Series
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Microorganisms Collected from the Surface of Freshwater Lakes Using a Drone Water Sampling System (DOWSE)

1
School of Plant and Environmental Sciences, Virginia Tech, Blacksburg, VA 24061, USA
2
Institute of Materials Chemistry (E165), TU Wien, 1060 Vienna, Austria
3
Civil and Environmental Engineering, Virginia Tech, Blacksburg, VA 24061, USA
*
Author to whom correspondence should be addressed.
Water 2019, 11(1), 157; https://doi.org/10.3390/w11010157
Submission received: 26 October 2018 / Revised: 8 January 2019 / Accepted: 10 January 2019 / Published: 16 January 2019
(This article belongs to the Section Water Quality and Contamination)

Abstract

:
New tools and technology are needed to study microorganisms in freshwater environments. Little is known about spatial distribution and ice nucleation activity (INA) of microorganisms in freshwater lakes. We developed a system to collect water samples from the surface of lakes using a 3D-printed sampling device tethered to a drone (DOWSE, DrOne Water Sampling SystEm). The DOWSE was used to collect surface water samples at different distances from the shore (1, 25, and 50 m) at eight different freshwater lakes in Austria in June 2018. Water samples were filtered, and microorganisms were cultured on two different media types, TSA (a general growth medium) and KBC (a medium semi-selective for bacteria in the genus Pseudomonas). Mean concentrations (colony forming units per mL, or CFU/mL) of bacteria cultured on TSA ranged from 19,800 (Wörthersee) to 210,500 (Gosaulacke) CFU/mL, and mean concentrations of bacteria cultured on KBC ranged from 2590 (Ossiachersee) to 11,000 (Vorderer Gosausee) CFU/mL. There was no significant difference in sampling distance from the shore for concentrations of microbes cultured on TSA (p = 0.28). A wireless bathymetry sensor was tethered to the drone to map temperature and depth across the sampling domain of each of the lakes. At the 50 m distance from the shore, temperature ranged from 17 (Hinterer Gosausee, and Gosaulacke) to 26 °C (Wörthersee), and depth ranged from 2.8 (Gosaulacke) to 11.1 m (Grundlsee). Contour maps of concentrations of culturable bacteria across the drone sampling domain revealed areas of high concentrations (hot spots) in some of the lakes. The percentage of ice-nucleation active (ice+) bacteria cultured on KBC ranged from 0% (0/64) (Wörthersee) to 58% (42/72) (Vorderer Gosausee), with a mean of 28% (153/544) for the entire sample set. Future work aims to elucidate the structure and function of entire microbial assemblages within and among the Austrian lakes.

Graphical Abstract

1. Introduction

Microorganisms play important roles in freshwater ecosystems [1]. Some bacteria are decomposers, breaking down organic matter into nitrate, phosphate, and other essential nutrients [1]. The diversity and abundance of microorganisms in lakes can drastically change the water quality of a freshwater system [2]. Cyanobacteria obtain their energy from photosynthesis and provide an important link in the food chain as they introduce oxygen and energy from the sun’s light to freshwater systems [1].
Freshwater lakes are an important source of microbial ice nucleators—microorganisms that facilitate the heterogeneous formation of ice at temperatures above −8 °C [3]. Pietsch et al. [3] collected strains of the bacterium Pseudomonas syringae from the surface of a freshwater lake in Virginia at different locations, and reported significantly more ice nucleation active (INA or ice+) strains in the fall and the winter compared to the spring. Ice-nucleating strains of P. syringae may aerosolize at greater rates than those that are not ice nucleators [4], and there could be a potential role for these ice nucleating strains of bacteria in precipitation processes [5,6]. The presence of biological particles has been reported in clouds and could impact precipitation at concentrations high enough to catalyze heterogeneous ice nucleation [7,8].
Water samples have traditionally been collected using devices such as Nansen bottles [9], Van Dorn samplers [10], or syringes [11]. These devices are usually actuated using a messenger dropped from the surface on the line, a bottom-induced trigger, or a powered servo (for large sampling cassettes). Recently, there has been an increasing interest in the development and use of unmanned robotic systems for collecting and characterizing samples in aquatic environments. Powers et al. [12] developed an unmanned surface vehicle (USV) to collect microorganisms at two different depths in a freshwater lake. This same USV platform was modified to collect microorganisms in aerosols above freshwater and saltwater environments [13].
New technologies with unmanned aerial systems (UASs, or drones) may assist in collecting water samples in remote areas, hard-to-reach environments, and in settings where hazardous agents may be present in the environment. Ore et al. [14] developed an autonomous drone platform for collecting water samples in aquatic environments. This system used a pump, a short hose, and three 25 mL vials that were filled by a rotating nozzle at the end of the hose. Koparan et al. [15] designed a small 3D-printed Van Dorn sampler for collecting water samples with a drone. This device was triggered by a messenger that was dropped down a cable from the drone. One of the limitations of both of these systems is the potential for cross-sample contamination, since the same device was used for collecting multiple samples. Consequently, new drone water sampling systems are needed to collect water samples without the potential for contamination across samples. Such drone water-sampling systems would be useful for collecting microorganisms that could be causal agents of disease.
In this manuscript, we report the development of a system to collect water samples from the surface of lakes for microbiological analyses using a 3D-printed sampling device tethered to a drone (DOWSE, DrOne Water Sampling SystEm). The sampling device was designed around a sterile 50 mL conical tube, enabling the collection and characterization of microbes without the potential for cross-contamination across samples. This sampling device is an extension of the traditional methods for water sampling (e.g., Nansen and Van Dorn samplers), without the need for an actuated mechanism to collect samples at the water surface [15]. We hypothesized that (1) concentrations of culturable microorganisms in freshwater lakes would vary with distance from the shore and (2) the frequency of ice-nucleating strains of Pseudomonas spp. would vary across different freshwater lakes. Our first hypothesis was based on the observation by Powers et al. [12] that there were significantly different concentrations of bacteria at different locations in Claytor Lake, Virginia. Our second hypothesis was based on the observations of Pietsch et al. [3] that the frequency of ice nucleating microbes varied with season, suggesting a temperature-dependent association with this phenotype (i.e., lakes with different temperatures could have different percentages of ice nucleating microorganisms). These hypotheses need to be tested to inform appropriate sampling strategies for microbes at the water surface, and to better understand the diversity and function of ice nucleating microorganisms in aquatic environments. To test these hypotheses, we used the DOWSE to collect surface water samples at different distances from the shore (1, 25, and 50 m) at eight different freshwater lakes in Austria in June 2018. Water samples were filtered, and microorganisms were cultured on two different media types (TSA and KBC). To our knowledge, this is the first report of a drone water sampling system for studying microorganisms in aquatic habitats. Such a system has the potential to be used in a variety of hard-to-reach aquatic environments, such as high-altitude alpine lakes and ponds.

2. Materials and Methods

2.1. DOWSE: DrOne Water Sampling SystEm

We developed a system to collect water samples from the surface of lakes using a 3D-printed sampling device carrying a 50 mL sterile conical tube tethered to a drone (DOWSE, DrOne Water Sampling SystEm). The water sampler consisted of four separate 3D-printed pieces (.stl files are available here: https://github.com/SchmaleLab/Schmale-Lab-3D-Printing-Files-Benson-et-al-Water-2018) assembled with 2.5 mm stainless steel screws (Figure 1).
The sampler was tethered to the center of a carbon fiber beam between two 3D-printed mounts attached the landing gear of the drone. The tether between the drone and the sampling device consisted of a fluorescent orange nylon string and was 4.5 m long (Figure 2a), and a carabiner was used to quickly attach and remove the water sampler following a sampling mission (Figure 2b). The DOWSE was used to collect samples at three locations 25 m from the nearest shore, and three locations 50 m from the nearest shore. A fishing rod tied to a fluorescent nylon string 2 m in length was used to collect water samples 1 m from the nearest shore with the same 3D-printed device that was tethered to the drone.
The drone was a Phantom 4 quadcopter (DJI, Shenzhen, China) powered by a 5870 mAh Lithium-ion polymer battery. This battery provided a safe, operational flight time of about 20 min. The Waypoint Intelligent Flight mode in the DJI GO 4 app was used to establish a grid of defined GPS waypoints equidistant from one another in a X, Y Cartesian plane. Three waypoints were 50 m from the nearest shore, three waypoints were 25 m from the nearest shore, and three waypoints were 1 m from the nearest shore (Figure 3).
After the GPS waypoints were established, the sampling device was loaded with a sterile 50 mL conical tube, and the drone was flown manually to each waypoint location to collect samples. Once the drone reached the sampling location, it descended to the surface of the water and allowed the sampling device to rest on the surface for a few seconds. During this time, the sampling device filled with water. An overhead image was then taken of the sampling device in the water (Figure 2c), which provided a precise record of the location and sampling time embedded in the Exif file of each of the images. Following each collection, the sample was returned to the shore and the 50 mL tube (now containing a sample of water) was switched out with a new tube while the drone was still in flight (Figure 2b). The drone then flew to another waypoint to collect another sample, until all targeted collections had been completed (Figure 2a).

2.2. Lake and Sampling Site Selection

Eight different freshwater lakes were sampled in Austria including Altausseersee (ALT), Grundlsee (GRU), Toplitzsee (TOP), Vorderer Gosausee (GOS), Gosaulacke (GOL), Hinterer Gosausee (HIN), Wörthersee (WOR), and Ossiachersee (OSS) (Table 1). Sites for sampling each lake were selected based on the availability of a safe and obstruction-free landing zone for the drone. Lakes were sampled 1, 25, and 50 m from the shore line. Personnel and equipment were located at the water’s edge, or on available dock space, except for Ossiachersee (OSS) where operations were carried out in the water about 8 m from the shore line. In order to pilot the drone, clearance was needed in front of the pilot point location area (Figure 3) with a minimum of 5 m of clearance on either side. The drone required space to hover above the pilot location in order for samples to be returned and allow for new collection tubes to be inserted into the sampler. These sites were also chosen to be minimally intrusive to the residents and others in the area by selecting sites that were away from other people at the time of sampling. Permissions to sample the lakes in June 2018 as part of this project were granted by the Austrian Federal Forests AG, DI Martin Heinz Stürmer, 3 April 2018.

2.3. Drone Bathymetry System

After all water samples were collected in a lake, a wireless bathymetry sensor (the Deeper ProPlus, Deeper, Vilnius, Lithuania) was tethered to the drone to map the temperature and depth from the shore line to 50 m from the shore (doing this after the water sampling minimized the mixing of water across the sampling domain, since the sensor was pulled through the water by the drone). The string length from the drone was 1.64 m to a line connection point with a 32 g weight, followed by a secondary connection, 1.20 m from the connection point to the bathymetry sensor. The weight was used to stabilize the line during windy conditions, and to facilitate a more controlled drag through the water. The bathymetry sensor was dragged through the water by the drone to a 50 m sampling position in the lake while continuously recording depth, GPS coordinates, and temperature of the water at one second intervals. The sensor was set to onshore GPS mode.

2.4. Filtering of Samples

Lake samples were processed on the same day that they were collected. Each 100 mL sample was poured into a single use, sterile Microfunnel 0.2 μm Gidded disposable Pall filter funnel (VWR International, Radnor, PA, USA, #28143-542). The lid was closed, and each unit was fitted onto a 500 mL filtration flask. A water jet pump (VWR International, Radnor, PA, USA, #181-9100) was used to vacuum filter each sample through the 0.22 μm filter. The filter assembly was dismantled, and the filter was recovered and transferred to a sterile 15 mL conical tube for shipping. The conical tubes with filters were separated into bags representing the lake they were collected in and stored at 4 °C until all samples were collected. All lake samples were shipped together in a cooler with ice packs.

2.5. Culturing of Microbes

Filters were stored at 4 °C for up to two weeks. The filters were taken from refrigerated storage and placed into sterile 100 mL glass bottles with 4 mL deionized (DI) water and a sterile stir bar. The bottles were set on a stir plate and the suspension was stirred for 10 min to lift microbes from the filter into the 4 mL resuspension water, resulting in a 25× concentration of collected lake sample. Aliquots of 1 mL of this water were serially diluted in 9 mL tubes, resulting in a 2.5× concentration, 0.25 dilution, and 0.025 dilution. Microbes from each sample site location were plated once at two different concentrations, on both TSA, and KBC agar plates. Aliquots of 200 μL of the 25× and 2.5× concentration were spread onto KBC media with the antibiotic cephalexin and cycloheximide, a eukaryotic protein synthesis inhibitor used to stop fungal growth. The KBC medium is semi-selective for bacteria in the genus Pseudomonas [16]. Aliquots of 200 μL of each remaining dilution (0.25 and 0.025) were spread on plates of Tryptone Soya Agar (TSA) media containing cycloheximide. Negative controls were plated with 200 μL of sterile water.

2.6. Quantification of Microbes from Plates

Pictures were taken of the TSA 0.025 dilution plates and of the 2.5× concentration KBC plates. These pictures were uploaded and analyzed using OpenCFU (Quentin Geissmann, Berlin, Germany, Version 3.8.11) an open source software for counting colonies. OpenCFU was utilized to count one half of the plate, and counts were modified manually to correct for false positive and false negative counts. The final corrected plate count value was used to calculate CFU/mL for each filter location, for TSA, and for KBC.

2.7. Contour Maps of Microbe Concentrations

To visualize the distribution of microbes across each of the lakes studied, contour maps were created using the CFU/mL data collected from both sets of media using Surfer 15 software (Golden Software, Golden, CO, USA). Concentration data for TSA and KBC was plotted on an X, Y Cartesian plane with distance in each dimension measured from the designated pilot start point (Figure 3). This grid file was then used to create a contour map with a color relief overlay.

2.8. Ice Nucleation Assays

A series of ice nucleation assays (INA) were conducted with a subset of colonies from each of the lakes. Eight colonies were selected at random from each plate of KBC from each of the eight sampling locations. A maximum of 72 colonies from each lake were screened for the ice+ phenotype. These colonies were picked with a sterile wooden tooth pick and deposited into 140 μL of sterile DI water in a 96-well plate. When growth from a low dilution plate was absent, colonies from the higher dilution plate of the same media type were picked. The 96-well assay plates were stored at 4 °C overnight, and then pulse-vortexed for 30 s and incubated at 4 °C for an additional hour. A multichannel pipet was used to transfer duplicate rows of 12 μL drops onto a PARAFILM® M (Sigma, St. Louis, MO, USA, P6543) float assembly in a Cryo bath circulator Lauda Alpha RA 12 (LCKD 4908) cooling bath (LAUDA-Brinkmann, LP, Delran, NJ 08075, USA) with ethylene glycol coolant fluid (Air gas RAD64000246). The circulator was set to −6 °C, and the temperature dropped first to −7 °C, then −8 °C with one-minute incubation intervals at each temperature and a final incubation time of 10 min at −8 °C.

2.9. Statistical Analyses

Statistical analyses were performed in JMP 14 (SAS, Cary, NC, USA) to test our hypotheses that (1) concentrations of culturable microorganisms in freshwater lakes would vary with distance from the shore and (2) the frequency of ice-nucleating strains of Pseudomonas spp. would vary across different freshwater lakes. An analysis of variance (ANOVA) was used to test for significant differences in concentrations of culturable bacteria between the three sampling distances across all of the lakes, and when controlling for the lake studied. Gosaulacke (GOL) was excluded from these tests, since this lake was not wide enough to allow the collection of samples 50 m from each shore. Tukey’s Honest Significant Difference (HSD) was used to test for differences in concentrations of culturable microbes at each of the sampling locations within a lake. ANOVA was used to test for significant differences in concentrations of culturable microbes at different sampling distances across all of the lakes, when controlling for lake depth and temperature. ANOVA and Tukey’s HSD were used to test for differences in the frequency of ice+ bacteria at different distances from the shore in each of the lakes. ANOVA was also used to test for differences in the altitude of the sample sites and the total percent of colonies that were ice nucleation active at −8 °C.

3. Results

Eight freshwater lakes in Austria were sampled with the DOWSE system in June 2018 (Table 1). Mean concentrations of culturable bacteria across all of the lakes for all distances combined were 73,496 CFU/mL on TSA. Mean concentrations of culturable bacteria for each of the individual lakes for all distances combines ranged from 19,800 (WOR) to 215,000 CFU/mL (GOL) on TSA, and 2600 (OSS) to 11,000 CFU/mL (GOS) on KBC.

3.1. Microbes Cultured from Different Distances in the Lake

Mean concentrations of culturable bacteria on TSA across all of the lakes sampled were 91,500 CFU/mL at 1 m from the shore, 66,600 CFU/mL at 25 m from the shore, and 61,000 CFU/mL at 50 m from the shore (Figure 4a). Mean concentrations of culturable bacteria on KBC media across all lakes were 5860 CFU/mL at 1 m from the shore, 8410 CFU/mL at 25 m from the shore, and 5000 CFU/mL at 50 m from the shore (Figure 4b). Concentrations of culturable microorganisms did not vary significantly with distance from the shore for bacteria cultured on TSA (p = 0.28) or KBC (p = 0.22). However, concentrations of culturable bacteria on KBC varied significantly between 1 and 50 m sampling distances in Toplitzsee (p = 0.03).
Mean concentrations of culturable bacteria on TSA across all of the lakes at 1 m from the shore ranged from 19,800 (Wörthersee) to 215,300 (Gosaulacke) CFU/mL (GOL was removed from statistical analyses since it was an outlier). For a sampling distance of 25 m from the shore, concentrations ranged from 29,100 (Wörthersee) to 74,400 (Ossiachersee) CFU/mL. For a sampling distance of 50 m from the shore, concentrations ranged from 86,700 (Wörthersee) to 98,100 (Ossiachersee) CFU/mL.
Mean concentrations of culturable bacteria on KBC across all of the lakes at 1 m from the shore ranged from 1130 (Toplitzsee) to 16,400 (Grundlsee) CFU/mL. For a sampling distance of 25 m from the shore, concentrations ranged from 54,100 (Gosaulacke) to 13,300 (Toplitzsee) CFU/mL. For a sampling distance of 50 m from the shore, concentrations ranged from 908 (Ossiachersee) to 7500 (Vorderer Gosausee) CFU/mL.

3.2. Spatial Distribution of Microbes Cultured from Each of the Lakes

Contour maps were used to examine the spatial distribution of microbes cultured from each of the lakes on TSA (Figure 5) and KBC (Figure 6). The contour map for microbes cultured on TSA from Altaussee showed a fairly uniform distribution of bacteria across the sampling domain (Figure 5). The contour map for bacteria cultured on TSA from Vorderer Gosausee, however, showed that concentrations of bacteria tended to decrease at greater distances from the shore. Interestingly enough, the contour map for bacteria cultured on KBC for Vorderer Gosausee showed that there were comparatively high concentrations of Pseudomonas-like bacteria in the same areas of the sampling grid that had lower concentrations on TSA (Figure 6). Overall, the contour maps revealed that within a sampling grid, there are certain sections with increased (peaks) or decreased (valleys) concentrations of bacteria in relation to the rest of the sampling grid.
Concentrations of bacteria cultured on TSA varied significantly with lake depth (p = 0.023) and with temperature (p < 0.001), but concentrations of bacteria cultured on KBC did not vary significantly with depth (p = 0.63) and temperature (p = 0.57).

3.3. Ice Nucleation Assays

The mean freezing rate of colonies tested from all lakes was 28% (Table 2). Vorderer Gosausee had a freezing rate of 83.33% based on 24 samples tested at 25 m (Table 2). When grouped by distance from shore sampled, there was no significant difference in the percentage of ice+ bacteria in the lakes (p = 0.17). However, when the data were grouped by individual lake, there was a significant difference in the percentage of ice+ bacteria (p = 0.03). This suggests that Pseudomonas-like ice+ strains were more abundant in some lakes than others, although the factors that influence this distribution is unknown. The ANOVA test run on lake altitude relative to percent of colonies that were ice(+), showed that elevation was not a significant factor (p = 0.20).

4. Discussion

New tools and technology are needed to study microorganisms in freshwater environments. Little is known about spatial distribution and ice nucleation activity (INA) of microorganisms in freshwater lakes. We developed a system to collect water samples from the surface of lakes using a 3D-printed sampling device tethered to a drone (DOWSE, DrOne Water Sampling SystEm). The DOWSE was used to collect surface water samples at different distances from the shore (1, 25, and 50 m) at eight different freshwater lakes in Austria in June 2018. Water samples were filtered, and microorganisms were cultured on two different media types (TSA and KBC). Our work extends the drone water sampling concept developed by Ore et al. [14] and Koparan et al. [15]. To our knowledge, this is the first report of a drone water sampling system for studying microorganisms in aquatic habitats.
Mean concentrations of microbes cultured on TSA ranged from 19,800 (Wörthersee) to 215,300 (Gosaulacke) CFU/mL, and mean concentrations of microbes cultured on KBC ranged from 2590 (Ossiachersee) to 10,969 (Vorderer Gosausee) CFU/mL. These ranges in concentration are much lower than those reported in Claytor Lake in southwest Virginia, USA [3]. The mean concentration of bacteria from the Claytor Lake surface samples between 2 May 2016 and 7 June 2016 on TSA was 5.20 × 108 CFU/mL, and on KBC media was 1.27 × 107 CFU/mL. The larger concentrations of bacteria measured in Claytor Lake could reflect differences in the collection sites. Claytor Lake is a reservoir without glacial inputs, and with a comparatively larger watershed for nutrients to be collected before running into the lake [17]. The alpine lakes sampled in this study have relatively small watersheds, and likely have much a more limited supply of the nutrients required for bacterial growth [17]. Another potential explanation for the lower concentrations in the Austrian lakes could be the amount of time from sample collection to plating; due to the remote nature of the study sites and the need to transport the samples to another country, the sample filters were plated on culture media within about two weeks. It is possible that there could have been a loss in viability during storage, potentially underestimating the actual culturable diversity in the lakes. However, since all of the samples were processed following similar storage times, any potential loss of viability would have likely been similar for all of the samples collected in this study.
There was no significant difference in sampling distance from the shore for concentrations of bacteria cultured on TSA and KBC, with the exception of lake Toplitzsee. With this sole exception, these results suggest that either the general bacterial and Pseudomonas populations are randomly distributed around the surface waters of the lakes, or that there is some other factor that influences this distribution that was not tested for in this study. There may be some factor found in Toplitzsee lake that is not found in the other lakes studied that results in the difference between the 1 and 50 m distance from shore. Cole et al. [18] found that bacterial concentrations are generally consistent in all depths of stratified lakes’ epilimnion. Powers et al. [12] came to a similar conclusion when comparing concentrations of bacteria collected at 5 and 50 cm below the surface of the water at Claytor Lake, Virginia, USA. Pietsch et al. [3] found that there was no significant difference between the surface water and water sampled at depths down to 9 m in bacterial concentration in Claytor Lake. Thus, we hypothesize that similar distributions of bacteria are likely to be found at different depths below the surface of the Austrian lakes, but this was not tested in the current study.
Concentrations of bacteria cultured on TSA varied significantly with lake depth and within the range of temperatures measured (17.7–25.0 °C), but concentrations of bacteria cultured on KBC did not vary significantly with depth and temperature. Thus, the depth of the lake may have an impact on the concentrations of many of the culturable bacteria at the lake surface, but not for Pseudomonas-like bacteria. Pietsch et al. [3] reported a similar range in surface water temperatures when sampling the surface water of Claytor Lake in southwest Virginia, USA between the May and June sampling dates. However, the temperature ranges from their study did not include distance from shore or depth of measurement. Alvarez et al. [19] generated a bathymetric map of Finn Creek Site 21 Reservoir in McCain County, Central Oklahoma, USA using a small unmanned aerial system (sUAS), and attached a floating data collector similar to the system used in our study. The coupling of aerial drone and bathymetric data collectors provides a quick and accurate means to map lakes [19]. Perhaps unmanned systems could be tuned to predict concentrations of bacteria in lakes, provided parameters such as temperature and depth can be measured remotely.
Contour maps of concentrations of microbes across the drone sampling domain revealed areas of high concentrations (hot spots) in some of the lakes. However, there were no repeating patterns in the concentrations of bacteria between lakes that suggested a trend between the lakes in relation to the distance samples were taken from the shore. Schmale et al. [20] showed both random and aggregated patterns of spore deposition in corn canopies over 2 years. The sampling grids used to generate their contour maps contained 12 to 16 discrete sample sites. This would suggest that additional data sets with expanded sampling locations from a designated origin in two dimensions could provide for a more robust analysis. An expanded collection of specific environmental variables could allow for a more complex analysis, such as a four-factor principal components analaysis (PCA) study that could elucidate trends in spatial and temporal variables and provide a determination ranking among collected data sets to show specific environmental factors that have a higher influence on observed environmental variance. In a four component PCA study with multiple environmental categories, Iizuka et al. [21] showed which environmental components contributed to the variance of the sample set. It should also be noted that contour maps of concentrations of bacteria could be influenced by currents in the lake, including water inputs near the sampling grid. Wind pushing and mixing the water in the lakes could influence the concentrations of bacteria on the surface of the lakes inside the sampling grid [18]. If the wind can transfer enough energy to the water, the composition of bacteria at the surface may change due to mixing of the water and nutrients. The effect of this vertical mixing could alter the concentration of surface waters as bacteria compete for these nutrients [22]. The wind could also aerosolize the bacteria and even transport them among lakes [19,20,21]. One limitation of our study is that we did not collect any water quality data from our samples (e.g., pH, nutrients, chlorophyll, dissolved organic carbon, and conductivity), which could help explain some of the observed differences within and among the lakes sampled during our campaign. Future work should consider obtaining these environmental data, which will also likely need to include an expansion of the sampling device to obtain larger sample volumes during collection.
The percentage of ice+ microbes cultured on KBC (selective for bacteria in the genus Pseudomonas) was significantly different across all the lakes sampled, and ranged from 0% (0/64) (Wörthersee) to 58% (42/72) (Vorderer Gosausee), with a mean of 28% (153/544) for the entire sample set. Samples that showed an ice+ phenotype by freezing in the droplet assay at −8 °C support previous literature that biogenic ice nucleators influence water to freeze at temperatures warmer than anthropogenic ice nucleators [23,24]. Over 90% (actual/numbers here) of colonies tested froze after loading the drops onto the float assembly at the pre-cooled temperature of −6 °C. This consistent frequency of freezing from colonies that were picked from KBC plates suggests that the glacial lake systems in this study contain ice+ bacteria that belong to the genus Pseudomoas. This average is much higher than would be expected, based on the findings of Pietsch et al. [3], where the mean ice+ percentage in samples collected in spring and early summer was 0.49%. These authors found that the time of year had a significant influence on the percentage of ice+ strains that were found. As the percentage of ice+ strains was so much higher in the Austrian lakes sampled, there are likely to be a suite of factors that makes it more advantageous for these strains to be present later in the year in the lakes studied in Austria. Altitude of the lakes sampled did not have a significant impact on the percentage of ice+ bacteria collected at the different lakes sampled. Although there was a positive trend between elevation above sea level and percent of colonies that were ice+, this was not significant. If more alpine lakes were sampled, perhaps the additional data points would strengthen these observations. GRU (43% ice+) is downstream relative to TOP (18% ice+), and had a higher percentage of ice+ bacteria, suggesting that in the months immediately following glacial melt, ice+ bacteria flow down and accumulate in lower altitudes. This trend held true for the higher altitude lake, HIN (32% ice+) relative to the lower altitude lake, GOS (58%). For lakes in close proximity that share the same source of glacial run-off, the lower altitude lakes had a higher percentage of ice-nucleating bacteria. Lake size, depth, and/or surface area could be a significant factor in the percent of bacteria that exhibit the ice+ phenotype throughout the year and warrants further study. Altitude might also play a role in the source sink relationship for ice nucleation activity, particularly in the context of our connected high-altitude lakes sampled on 7 June and 8 June 2018. The highest altitude site in a cluster of three lakes is referred to as the “source” lake, while the lowest altitude lake is referred to as the sink lake. We observed an increase in ice nucleation activity in the “sink” lake during the month of June 2018. Interestingly, the “source” lake located in the highest altitude, showed a higher percentage of ice nucleation activity than the mid-altitude, or “flow-thru” lake. Samples were taken during active thawing. The lowest percentage of ice nucleators in the “flow-thru” lakes, could indicate that those lakes are providing transport during the active thaw cycle.
Our drone water sampling system was designed to inform appropriate sampling strategies for microbes at the water surface, and to better understand the diversity and function of ice nucleating microorganisms in aquatic environments. Our system has the potential to be used in a variety of hard-to-reach aquatic environments, such as high-altitude alpine lakes and ponds. The DOWSE sampler could be used to identify and track potential toxins, and contribute to efforts aimed at finding causes of these harmful blooms [25,26,27]. This system allows water sampling near the shore line without any major disturbances or mixing of the sample area. Future work aims to elucidate the structure and function of entire microbial assemblages within and among the Austrian lakes; diversity analyses of culturable plate growth on the non-selection TSA media could be determined by 16S sequence analysis [28]. Additional analyses of the abundance of ice+ bacteria in surrounding bodies of water, such as glacial streams and rivers, could also be conducted to determine sources and reservoirs of ice nucleating microorganisms.

Author Contributions

J.B. and R.H. participated in conceptualization, investigation, formal analysis, data curation, and writing—original draft preparation. P.B. and T.M.S. participated in investigation and writing—review and editing. C.W.P. participated in methodology. H.G. and D.G.S.III participated in conceptualization, investigation, writing—original draft preparation, supervision, project administration, and funding acquisition.

Funding

This research was supported by grants to D. Schmale from the Institute of Critical Technology and Applied Science (ICTAS) at Virginia Tech (#177220), the College of Agriculture and Life Sciences at Virginia Tech (#137605), and the National Science Foundation (NSF) under Grant Numbers DEB-1241068 [Dimensions: Collaborative Research: Research on Airborne Ice-Nucleating Species (RAINS)], AGS-1520825 (HAZARDS SEES: Uncovering the Hidden Skeleton of Environmental Flows: Advanced Lagrangian Methods for Hazard Prediction, Mitigation, and Response), and IIS-1637915 (NRI: Coordinated Detection and Tracking of Hazardous Agents with Aerial and Aquatic Robots to Inform Emergency Responders). This research was supported by grants to H. Grothe from the Austrian Science Fund (FWF) under Grant P26040, and bridge project 850689 [EarlySnow] from the Austrian Research Promotion Agency (FFG). Any opinions, findings, and conclusions or recommendations expressed in this material are those of the authors and do not necessarily reflect the views of the sponsors of this research.

Acknowledgments

The authors would like to thank Martin Heinz Stürmer (Österreichische Bundesforste AG) and the Austrian Federal Forests AG for the support and permission to sample the lakes.

Conflicts of Interest

The authors declare no conflict of interest.

References

  1. Newton, R.J.; Jones, S.E.; Eiler, A.; McMahon, K.D.; Bertilsson, S. A guide to the natural history of freshwater lake bacteria. Microbiol. Mol. Biol. Rev. 2011, 75, 14–49. [Google Scholar] [CrossRef] [PubMed]
  2. Kurilkina, M.I.; Zakharova, Y.R.; Galachyants, Y.P.; Petrova, D.P.; Bukin, Y.S.; Domysheva, V.M.; Blinov, V.V.; Likhoshway, Y.V. Bacterial community composition in the water column of the deepest freshwater Lake Baikal as determined by next-generation sequencing. FEMS Microbiol. Ecol. 2016, 92, fiw094. [Google Scholar] [CrossRef] [PubMed]
  3. Pietsch, R.B.; Vinatzer, B.A.; Schmale, D.G., III. Diversity and abundance of ice nucleating strains of Pseudomonas syringae in a freshwater lake in Virginia, USA. Front. Microbiol. 2017, 8, 318. [Google Scholar] [CrossRef] [PubMed]
  4. Pietsch, R.B.; David, R.F.; Marr, L.C.; Vinatzer, B.; Schmale, D.G., III. Aerosolization of Two Strains (Ice+ and Ice–) of Pseudomonas syringae in a Collison Nebulizer at Different Temperatures. Aerosol Sci. Technol. 2015, 49, 159–166. [Google Scholar] [CrossRef]
  5. Sands, D.C.; Langhans, V.E.; Scharen, A.L.; De Smet, G. The association between bacteria and rain and possible resultant meteorological implications. Idojaras 1982, 86, 2–4. [Google Scholar]
  6. Morris, C.E.; Conen, F.; Alex Huffman, J.; Phillips, V.; Pöschl, U.; Sands, D.C. Bioprecipitation: A feedback cycle linking Earth history, ecosystem dynamics and land use through biological ice nucleators in the atmosphere. Glob. Chang. Biol. 2014, 20, 341–351. [Google Scholar] [CrossRef] [PubMed]
  7. Creamean, J.M.; Suski, K.J.; Rosenfeld, D.; Cazorla, A.; DeMott, P.J.; Sullivan, R.C.; White, A.B.; Ralph, F.M.; Minnis, P.; Comstock, J.M. Dust and biological aerosols from the Sahara and Asia influence precipitation in the western US. Science 2013, 339, 1572–1578. [Google Scholar] [CrossRef]
  8. Pratt, K.A.; DeMott, P.J.; French, J.R.; Wang, Z.; Westphal, D.L.; Heymsfield, A.J.; Twohy, C.H.; Prenni, A.J.; Prather, K.A. In situ detection of biological particles in cloud ice-crystals. Nat. Geosci. 2009, 2, 398–401. [Google Scholar] [CrossRef]
  9. Kriss, A.E.; Lebedeva, M.N.; Tsiban, A.V. Comparative estimate of a Nansen and microbiological water bottle for sterile collection of water samples from depths of seas and oceans. Deep Sea Res. Oceanogr. Abstr. 1966, 13, 205. [Google Scholar] [CrossRef]
  10. Van Dorn, W.G. Large-volume water samplers. Eos Trans. Am. Geophys. Union 1956, 37, 682–684. [Google Scholar] [CrossRef]
  11. Schindler, D.W. Two useful devices for vertical plankton and water sampling. J. Fish. Board Can. 1969, 26, 1948–1955. [Google Scholar] [CrossRef]
  12. Powers, C.; Hanlon, R.; Schmale, D.G., III. Remote collection of microorganisms at two depths in a freshwater lake using an unmanned surface vehicle (USV). PeerJ 2018, 6, e4290. [Google Scholar] [CrossRef] [PubMed]
  13. Powers, C.W.; Hanlon, R.; Grothe, H.; Prussin, A.J. Coordinated Sampling of Microorganisms over Freshwater and Saltwater Environments using an Unmanned Surface Vehicle (USV) and a Small Unmanned Aircraft System (sUAS). Front. Microbiol. 2018, 9, 1668. [Google Scholar] [CrossRef] [PubMed]
  14. Ore, J.-P.; Elbaum, S.; Burgin, A.; Detweiler, C. Autonomous aerial water sampling. J. Field Robot. 2015, 32, 1095–1113. [Google Scholar] [CrossRef]
  15. Koparan, C.; Koc, A.B.; Privette, C.V.; Sawyer, C.B.; Sharp, J.L. Evaluation of a UAV-Assisted Autonomous Water Sampling. Water 2018, 10, 655. [Google Scholar] [CrossRef]
  16. Mohan, S.K.; Schaad, N.W. An improved agar plating assay for detecting Pseudomonas syringae pv. syringae and P. s. pv. phaseolicola in contaminated bean seed. Phytopathology 1987, 77, 1390–1395. [Google Scholar]
  17. Fraterrigo, J.M.; Downing, J.A. The influence of land use on lake nutrients varies with watershed transport capacity. Ecosystems 2008, 11, 1021–1034. [Google Scholar] [CrossRef]
  18. Cole, J.J.; Pace, M.L.; Caraco, N.F.; Steinhart, G.S. Bacterial biomass and cell size distributions in lakes: More and larger cells in anoxic waters. Limnol. Oceanogr. 1993, 38, 1627–1632. [Google Scholar] [CrossRef] [Green Version]
  19. Alvarez, L.; Moreno, H.; Segales, A.; Pham, T.; Pillar-Little, E.; Chilson, P. Merging Unmanned Aerial Systems (UAS) Imagery and Echo Soundings with an Adaptive Sampling Technique for Bathymetric Surveys. Remote Sens. 2018, 10, 1362. [Google Scholar] [CrossRef]
  20. Schmale, D.G., III; Shah, D.A.; Bergstrom, G.C. Spatial patterns of viable spore deposition of Gibberella zeae in wheat fields. Phytopathology 2005, 95, 472–479. [Google Scholar] [CrossRef]
  21. Iizuka, T.; Wadati, M. Soliton transmission and reflection in discontinuous media. J. Phys. Soc. Jpn. 1992, 61, 3077–3085. [Google Scholar] [CrossRef]
  22. Diao, M.; Sinnige, R.; Kalbitz, K.; Huisman, J.; Muyzer, G. Succession of bacterial communities in a seasonally stratified lake with an anoxic and sulfidic hypolimnion. Front. Microbiol. 2017, 8, 2511. [Google Scholar] [CrossRef] [PubMed]
  23. Coluzza, I.; Creamean, J.; Rossi, M.J.; Wex, H.; Alpert, P.A.; Bianco, V.; Boose, Y.; Dellago, C.; Felgitsch, L.; Fröhlich-Nowoisky, J.; et al. Perspectives on the Future of Ice Nucleation Research: Research Needs and Unanswered Questions Identified from Two International Workshops. Atmosphere 2017, 8, 138. [Google Scholar] [CrossRef]
  24. Hoose, C.; Möhler, O. Heterogeneous ice nucleation on atmospheric aerosols: A review of results from laboratory experiments. Atmos. Chem. Phys. 2012, 12, 9817–9854. [Google Scholar] [CrossRef]
  25. Ho, J.C.; Michalak, A.M. Challenges in tracking harmful algal blooms: A synthesis of evidence from Lake Erie. J. Gt. Lakes Res. 2015, 41, 317–325. [Google Scholar] [CrossRef] [Green Version]
  26. Anderson, D.M.; Glibert, P.M.; Burkholder, J.M. Harmful algal blooms and eutrophication: Nutrient sources, composition, and consequences. Estuaries 2002, 25, 704–726. [Google Scholar] [CrossRef]
  27. Watson, S.B.; Whitton, B.A.; Higgins, S.N.; Paerl, H.W.; Brooks, B.W.; Wehr, J.D. Harmful algal blooms. In Freshwater Algae of North America, 2nd ed.; Elsevier: Amsterdam, The Netherlands, 2014; pp. 873–920. [Google Scholar]
  28. Jimenez-Sanchez, C.; Hanlon, R.; Aho, K.A.; Powers, C.; Morris, C.E.; Schmale, D.G., III. Diversity and ice nucleation activity of microorganisms collected with a small unmanned aircraft system (sUAS) in France and the United States. Front. Microbiol. 2018, 9, 1667. [Google Scholar] [CrossRef]
Figure 1. Engineering diagram of the 3D-printed water sampler designed to hold a sterile 50 mL conical tube. The tube had a swinging bucket design (right), and was attached to the drone via a carabiner on a nylon string.
Figure 1. Engineering diagram of the 3D-printed water sampler designed to hold a sterile 50 mL conical tube. The tube had a swinging bucket design (right), and was attached to the drone via a carabiner on a nylon string.
Water 11 00157 g001
Figure 2. (a) The DrOne Water Sampling SystEm (DOWSE) preparing to collect a sample at Toplitzsee (TOP) in Austria; (b) The DOWSE returning from a sampling mission at TOP; (c) Overhead image of the sampling device in the water taken from the quadcopter. This provided a precise record of the location and sampling time which was embedded in the Exif file of each of the images.
Figure 2. (a) The DrOne Water Sampling SystEm (DOWSE) preparing to collect a sample at Toplitzsee (TOP) in Austria; (b) The DOWSE returning from a sampling mission at TOP; (c) Overhead image of the sampling device in the water taken from the quadcopter. This provided a precise record of the location and sampling time which was embedded in the Exif file of each of the images.
Water 11 00157 g002
Figure 3. Schematic of sampling plan for each of the lakes in Austria. All distances were measured in flight using GPS coordinates in the DJI GO 4 software. The lower right corner of the sampling grid was designated as the pilot start point and served as the take-off and landing site for all sample collections.
Figure 3. Schematic of sampling plan for each of the lakes in Austria. All distances were measured in flight using GPS coordinates in the DJI GO 4 software. The lower right corner of the sampling grid was designated as the pilot start point and served as the take-off and landing site for all sample collections.
Water 11 00157 g003
Figure 4. (a) Histogram of mean CFU/mL cultured on TSA agar media at the different distances from shore. Error bars represent the standard error. Values were calculated from counts obtained at each distance from shore (1, 25, and 50 m); (b) Histogram of mean CFU/mL cultured on KBC agar media at the different distances from shore. Error bars represent the standard error. Values were calculated from counts obtained at each distance from shore (1, 25, and 50 m).
Figure 4. (a) Histogram of mean CFU/mL cultured on TSA agar media at the different distances from shore. Error bars represent the standard error. Values were calculated from counts obtained at each distance from shore (1, 25, and 50 m); (b) Histogram of mean CFU/mL cultured on KBC agar media at the different distances from shore. Error bars represent the standard error. Values were calculated from counts obtained at each distance from shore (1, 25, and 50 m).
Water 11 00157 g004
Figure 5. Contour maps of the spatial distribution of bacteria (meters) cultured from each of the Austrian lakes on TSA agar media (CFU/mL). These contour maps were created using the Surfer 15 software using the concentration data for each sample site in each lake. The small area mini-lake, Gosaulacke (GOL), had an alternate sample collection grid. Sample collections were plotted on a Cartesian plane.
Figure 5. Contour maps of the spatial distribution of bacteria (meters) cultured from each of the Austrian lakes on TSA agar media (CFU/mL). These contour maps were created using the Surfer 15 software using the concentration data for each sample site in each lake. The small area mini-lake, Gosaulacke (GOL), had an alternate sample collection grid. Sample collections were plotted on a Cartesian plane.
Water 11 00157 g005
Figure 6. Contour maps of the spatial distribution of bacteria (meters) cultured from each of the Austrian lakes on KBC agar media (CFU/mL). These contour maps were created using the Surfer 15 software using the concentration data for each sample site in each lake. The small area mini-lake, Gosaulacke (GOL), had an alternate sample collection grid. Sample collections were plotted on a Cartesian plane.
Figure 6. Contour maps of the spatial distribution of bacteria (meters) cultured from each of the Austrian lakes on KBC agar media (CFU/mL). These contour maps were created using the Surfer 15 software using the concentration data for each sample site in each lake. The small area mini-lake, Gosaulacke (GOL), had an alternate sample collection grid. Sample collections were plotted on a Cartesian plane.
Water 11 00157 g006
Table 1. Lake name, abbreviation, GPS location, and size, and altitude for all lakes sampled during the campaign.
Table 1. Lake name, abbreviation, GPS location, and size, and altitude for all lakes sampled during the campaign.
Lake NameAbbreviationLongitude and LatitudeApproximate Area (km2)Elevation (meters)
AltausseeALT47°38′27.3′′ N 13°47′04.2′′ E2.1712
ToplitzseeTOP47°38′30′′ N 13°55′40′′ E0.54718
GrundlseeGRU47°37′51.1′′ N 13°51′23.2′′ E4.1708
Vorderer GosauseeGOS47°31′28.1′′ N 13°30′52.7′′ E0.67917
GosaulackeGOL47°30′58.3′′ N 13°31′42.8′′ E0.04978
Hinterer GosauseeHIN47°30′07.8′′ N 13°33′00.1′′ E0.311151
WörtherseeWOR46°37′19.6′′ N 14°09′06.0′′ E19.4440
OssiacherseeOSS46°39′54.7′′ N 13°58′01.8′′ E10.8502
Table 2. Results from the ice nucleation assays for strains of Pseudomonas-like colonies cultured on KBC.
Table 2. Results from the ice nucleation assays for strains of Pseudomonas-like colonies cultured on KBC.
LakeDate of CollectionDistance Sampled (meters)Total Colonies FreezingTotal Colonies Tested% Colonies Freezing# Colonies Freezing at −8 °C
ALT7 June 201812248.330
ALT7 June 20182501600
ALT7 June 2018501166.251
TOP7 June 2018162425.000
TOP7 June 2018252248.331
TOP7 June 20185052420.830
GRU7 June 20181122450.000
GRU7 June 20182572419.170
GRU7 June 201850122450.000
GOS8 June 2018152420.831
GOS8 June 201825202483.331
GOS8 June 201850172470.831
GOL8 June 20181123237.53
GOL8 June 20182563218.750
HIN8 June 20181132454.174
HIN8 June 20182502400
HIN8 June 201850102441.670
WOR10 June 2018101600
WOR10 June 20182502400
WOR10 June 20185002400
OSS10 June 20181122450.001
OSS10 June 20182532412.501
OSS10 June 20185052420.830

Share and Cite

MDPI and ACS Style

Benson, J.; Hanlon, R.; Seifried, T.M.; Baloh, P.; Powers, C.W.; Grothe, H.; Schmale, D.G. Microorganisms Collected from the Surface of Freshwater Lakes Using a Drone Water Sampling System (DOWSE). Water 2019, 11, 157. https://doi.org/10.3390/w11010157

AMA Style

Benson J, Hanlon R, Seifried TM, Baloh P, Powers CW, Grothe H, Schmale DG. Microorganisms Collected from the Surface of Freshwater Lakes Using a Drone Water Sampling System (DOWSE). Water. 2019; 11(1):157. https://doi.org/10.3390/w11010157

Chicago/Turabian Style

Benson, James, Regina Hanlon, Teresa M. Seifried, Philipp Baloh, Craig W. Powers, Hinrich Grothe, and David G. Schmale. 2019. "Microorganisms Collected from the Surface of Freshwater Lakes Using a Drone Water Sampling System (DOWSE)" Water 11, no. 1: 157. https://doi.org/10.3390/w11010157

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Metrics

Back to TopTop